Title page for ETD etd-051799-162256

Type of Document Dissertation
Author Ratta, Varun
Author's Email Address vratta@vt.edu
URN etd-051799-162256
Title Crystallization, Morphology, Thermal Stability and Adhesive Properties of Novel High Performance Semicrystalline Polyimides
Degree PhD
Department Chemical Engineering
Advisory Committee
Advisor Name Title
Wilkes, Garth L. Committee Chair
Cox, David F. Committee Member
Davis, Richey M. Committee Member
Marand, Herv L. Committee Member
McGrath, James E. Committee Member
Ward, Thomas C. Committee Member
  • Morphology
  • Crystallization Kinetics
  • Thermal Stability
  • Lap-shear
  • Crystallization
  • Adhesive
  • Polyimides
Date of Defense 1999-04-26
Availability unrestricted
It was the objective of this research to develop high temperature and high performance polyimides that also display (a) thermal stability; (b) crystallinity in the initial material and ability to crystallize from the melt; (c) fast crystallization kinetics and (d) melt processability. This unique combination of properties is presently unavailable in any other polyimide. In this regard, the present work investigates the crystallization, morphology and thermal stability of two novel semicrystalline polyimides based on the same diamine, 1,3-bis (4-aminophenoxy) benzene (TPER), but two different dianhydrides, 3,3',4',4'-biphenyltetracarboxylic dianhydride (BPDA) and 3,3',4,4'-benzophenonetetracarboxylic dianhydride (BTDA). Phthalic anhydride was used as an endcapper to improve the thermal stability of the polyimides. The BPDA based polyimide was also tested extensively as a structural adhesive using Ti-6Al-4V coupons. Additionally, these polyimides are based on monomers, that are presently commercially available.

The bulk thermal stability of the polyimides was first evaluated using dynamic and isothermal thermogravimetric experiments. DSC was utilized to test the ability of the polyimides to crystallize from the melt after exposures to varying melt times and temperatures. Exceptional thermal stability was demonstrated by BPDA based polyimide with no change in the melting behavior after 40 min at 430°C or 30 min at 440°C. The semicrystalline morphology of the material was studied using hot stage polarized optical microscopy (OM) and atomic force microscopy. The spherulitic growth rates were determined as a function of crystallization temperature after quenching from various melt times and temperatures. The effect of crystallization temperature, previous melt time and melt temperature on the morphology was considered. The spherulitic growth rates increased with increasing undercooling in the temperature range studied (nucleation controlled), while the growth rate at a specific crystallization temperature decreased on increasing the previous melt time and temperature. The melting behavior was studied after different crystallization times and temperatures and also as a function of different heating rates. Crystallization kinetics was followed both isothermally and non-isothermally using DSC and OM. Avrami analysis was performed for TPER-BPDA and the obtained results were correlated with microscopic observations. Melt viscosity measurements were carried out as a function of melt temperature, melt time and frequency. The adhesive investigations for TPER-BTDA utilized lap-shear test, wedge test and double cantilever beam tests. The durability of the adhesive and the fracture surface was studied after exposure to various solvents and after high aging and testing temperatures. The polyimide demonstrated very high average room temperature lap-shear strengths (8400 psi or 59 MPa), excellent solvent resistance and durability of strengths at high aging and testing temperatures.

  Filename       Size       Approximate Download Time (Hours:Minutes:Seconds) 
 28.8 Modem   56K Modem   ISDN (64 Kb)   ISDN (128 Kb)   Higher-speed Access 
  1title.pdf 4.78 Kb 00:00:01 < 00:00:01 < 00:00:01 < 00:00:01 < 00:00:01
  2abstract.pdf 8.70 Kb 00:00:02 00:00:01 00:00:01 < 00:00:01 < 00:00:01
  3dedication.pdf 3.37 Kb < 00:00:01 < 00:00:01 < 00:00:01 < 00:00:01 < 00:00:01
  4acknowledgements.pdf 9.38 Kb 00:00:02 00:00:01 00:00:01 < 00:00:01 < 00:00:01
  5table.pdf 12.83 Kb 00:00:03 00:00:01 00:00:01 < 00:00:01 < 00:00:01
  6list.pdf 37.60 Kb 00:00:10 00:00:05 00:00:04 00:00:02 < 00:00:01
  introduction.pdf 10.12 Kb 00:00:02 00:00:01 00:00:01 < 00:00:01 < 00:00:01
  polyimide1.pdf 131.88 Kb 00:00:36 00:00:18 00:00:16 00:00:08 < 00:00:01
  polyimide2.pdf 780.84 Kb 00:03:36 00:01:51 00:01:37 00:00:48 00:00:04
  polyimide3.pdf 336.62 Kb 00:01:33 00:00:48 00:00:42 00:00:21 00:00:01
  polyimide4.pdf 622.13 Kb 00:02:52 00:01:28 00:01:17 00:00:38 00:00:03
  polyimide5.pdf 409.52 Kb 00:01:53 00:00:58 00:00:51 00:00:25 00:00:02
  polyimide6.pdf 1.11 Mb 00:05:08 00:02:38 00:02:18 00:01:09 00:00:05
  polyimide7.pdf 429.54 Kb 00:01:59 00:01:01 00:00:53 00:00:26 00:00:02
  polyimide8.pdf 516.51 Kb 00:02:23 00:01:13 00:01:04 00:00:32 00:00:02
  polyimide9.pdf 24.40 Kb 00:00:06 00:00:03 00:00:03 00:00:01 < 00:00:01
  vita.pdf 4.65 Kb 00:00:01 < 00:00:01 < 00:00:01 < 00:00:01 < 00:00:01

Browse All Available ETDs by ( Author | Department )

dla home
etds imagebase journals news ereserve special collections
virgnia tech home contact dla university libraries

If you have questions or technical problems, please Contact DLA.