Title page for ETD etd-10062007-151616

Type of Document Dissertation
Author Asare, Ted Ankomahene
Author's Email Address asare@vt.edu
URN etd-10062007-151616
Title Investigating Ferroelastic and Piezoelectric Vibration Damping Behavior in Nickel-Barium Titanate and Nickel-PZT Composites
Degree PhD
Department Materials Science and Engineering
Advisory Committee
Advisor Name Title
Kampe, Stephen L. Committee Chair
Aning, Alexander O. Committee Member
Pickrell, Gary R. Committee Member
Reynolds, William T. Jr. Committee Member
Schultz, Jeffery P. Committee Member
  • damping capacity
  • ferroelasticity
  • ferroelectricity
  • piezoelectricity
  • barium titanate
  • metal matrix composites
Date of Defense 2007-09-26
Availability unrestricted
Ferroelectric and piezoelectric ceramic reinforced metal matrix composites are new materials being explored for vibration damping purposes. The high damping ability of ferroelectric and piezoelectric ceramics such as barium titanate (BaTiO3) and lead zirconate titanate (PZT) is due to the anelastic response of ferroelastic domain walls to applied external stress. In piezoelectric ceramics, vibration energy can also be dissipated through the direct piezoelectric effect if the appropriate electric circuit is connected across the ceramic.

In this work we have examined the vibration damping behavior of BaTiO3, nickel-barium titanate (Ni-BaTiO3) composites and nickel-lead zirconate titanate (Ni-PZT) composites. BaTiO3 ceramics were fabricated by a combination of uniaxial pressing and cold isostatic pressing followed by sintering in air. Low frequency (0.1Hz-10Hz) damping capacity of BaTiO3, tanδ has been measured in three-point bend configuration on a dynamic mechanical analyzer. Tanδ has been found to increase with temperature up to the Curie temperature (Tc) of BaTiO3, after which there was a drop in damping capacity values due to the disappearance of ferroelectric domains above Tc. Furthermore within the frequency range tested, tanδ has been found to decrease with increasing vibration frequency. We also observed that tanδ decays with the number of vibration cycles (N). The decrease in tanδ with N, however, is fully recovered if BaTiO3 is heated above the Tc.

Ni-BaTiO3 composite composed of a layer of BaTiO3 ceramic sandwiched between two layers of Ni were fabricated using a combination of electroless plating and electroforming. The damping behavior of the composite was analyzed in terms of the damping mechanisms below Tc and the damping mechanisms above Tc of BaTiO3. Below Tc, vibration damping ability of the composite was highly influenced by ferroelastic damping in the BaTiO3 component. Above the Curie temperature, the damping capacity was influence more by the inherent damping mechanisms in the nickel matrix.

The damping mechanisms in Ni-PZT composites were evaluated at a low vibration frequency of 1Hz. In these composites we identified ferroelastic domain wall motion as the main damping mechanism active below the Tc of PZT. Using a poled PZT ceramic enhanced the damping capacity of the composite because of favorable ferroelastic domain orientation in the direction of applied stress. Based on our experimental results, we found no evidence of a direct piezoelectric damping mechanism in the Ni-PZT composites.

  Filename       Size       Approximate Download Time (Hours:Minutes:Seconds) 
 28.8 Modem   56K Modem   ISDN (64 Kb)   ISDN (128 Kb)   Higher-speed Access 
  ETD-FINAL.pdf 6.62 Mb 00:30:38 00:15:45 00:13:47 00:06:53 00:00:35

Browse All Available ETDs by ( Author | Department )

dla home
etds imagebase journals news ereserve special collections
virgnia tech home contact dla university libraries

If you have questions or technical problems, please Contact DLA.