Title page for ETD etd-112199-224339

Type of Document Dissertation
Author Chen, Buo
URN etd-112199-224339
Title Crack Path Selection in Adhesively Bonded Joints
Degree PhD
Department Engineering Mechanics
Advisory Committee
Advisor Name Title
Dillard, David A. Committee Chair
Case, Scott W. Committee Member
Dillard, John G. Committee Member
Gao, David Y. Committee Member
Lesko, John J. Committee Member
Love, Brian J. Committee Member
  • T-stress
  • adhesively bonded joints
  • cohesive failure
  • direction of cracking
  • mixed mode fracture
  • Locus of failure
  • interfacial failure
  • alternating failure
  • directional stability.
  • surface preparation
  • failure mode
  • crack path selection
Date of Defense 1999-11-15
Availability unrestricted
This dissertation is to obtain an overall understanding of the crack path selection in adhesively bonded joints. Using Dow Chemical epoxy resin DER 331® with various levels of rubber concentration as an adhesive, and aluminum 6061-T6 alloy with different surface pretreatments as the adherends, both symmetric and asymmetric double cantilever beam (DCB) specimens are prepared and tested under mixed mode fracture conditions in this study. Post-failure analyses conducted on the failure surfaces indicate that the failure tends to be more interfacial as the mode II component in the fracture increases whereas more advanced surface preparation techniques can prevent failure at the interface. Through mechanically stretching the DCB specimens uniaxially until the adherends are plastically deformed, various levels of T-stress are achieved in the specimens. Test results of the specimens with various T-stresses demonstrate that the directional stability of cracks in adhesive bonds depends on the T-stress level. Cracks tend to be directionally stable when the T-stress is compressive whereas directionally unstable when the T-stress is tensile. However, the direction of crack propagation is mostly stabilized when more than 3% mode II fracture component is present in the loading regardless of the T-stress levels in the specimens. Since the fracture sequences in adhesive bonds are closely related to the energy balance in the system, an energy balance model is developed to predict the directional stability of cracks and the results are consistent with the experimental observations. Using the finite element method, the T-stress is shown to be closely related to the specimen geometry, indicating a specimen geometry dependence of the directional stability of cracks. This prediction is verified through testing DCB specimens with various adherend and adhesives thicknesses. By testing the specimens under both quasi-static and low-speed impact conditions, and using a high-speed camera to monitor the fracture sequence, the influences of the debond rate on the locus of failure and the directional stability of cracks are investigated. Post-failure analyses suggest that the failure tends to be more interfacial when the debond rate is low and tends to be more cohesive when the debond rate is high. However, this rate dependence of the locus of failure is greatly reduced when more advanced surface preparation techniques are used in preparing the specimens. The post-failure analyses also reveal that cracks tend to be more directionally unstable as the debond rate increases. Finally, employing interface mechanics and extending the criteria for the direction of crack propagation to adhesively bonded joints, the crack trajectories for directionally unstable cracks are predicted and the results are consistent with the overall features of the crack paths observed experimentally.
  Filename       Size       Approximate Download Time (Hours:Minutes:Seconds) 
 28.8 Modem   56K Modem   ISDN (64 Kb)   ISDN (128 Kb)   Higher-speed Access 
  BCVita.pdf 2.71 Kb < 00:00:01 < 00:00:01 < 00:00:01 < 00:00:01 < 00:00:01
  Ch1-Figs.pdf 48.75 Kb 00:00:13 00:00:06 00:00:06 00:00:03 < 00:00:01
  ch1.pdf 24.60 Kb 00:00:06 00:00:03 00:00:03 00:00:01 < 00:00:01
  Ch2-Figs.pdf 713.95 Kb 00:03:18 00:01:41 00:01:29 00:00:44 00:00:03
  ch2.pdf 54.12 Kb 00:00:15 00:00:07 00:00:06 00:00:03 < 00:00:01
  Ch3-Figs.pdf 121.23 Kb 00:00:33 00:00:17 00:00:15 00:00:07 < 00:00:01
  ch3.pdf 61.62 Kb 00:00:17 00:00:08 00:00:07 00:00:03 < 00:00:01
  Ch4-Figs.pdf 497.58 Kb 00:02:18 00:01:11 00:01:02 00:00:31 00:00:02
  ch4.pdf 71.20 Kb 00:00:19 00:00:10 00:00:08 00:00:04 < 00:00:01
  Ch5-Figs.pdf 265.40 Kb 00:01:13 00:00:37 00:00:33 00:00:16 00:00:01
  ch5.pdf 70.50 Kb 00:00:19 00:00:10 00:00:08 00:00:04 < 00:00:01
  ch6.pdf 8.53 Kb 00:00:02 00:00:01 00:00:01 < 00:00:01 < 00:00:01
  front.pdf 28.41 Kb 00:00:07 00:00:04 00:00:03 00:00:01 < 00:00:01
  title.pdf 3.05 Kb < 00:00:01 < 00:00:01 < 00:00:01 < 00:00:01 < 00:00:01

Browse All Available ETDs by ( Author | Department )

dla home
etds imagebase journals news ereserve special collections
virgnia tech home contact dla university libraries

If you have questions or technical problems, please Contact DLA.